Solder Paste Mixer

1. Machine features Features:
1.1 Does not require prior mixing Paste ice back;
1.2 Do not have to open the container;
1.3 Power supply single-phase 220v:
1.4 No water vapor problem:
1.5 Does not destroy the shape of tin powder:
1.6 Fixture for all kinds of packaging solder paste cans;
1.7 Stirring time and stirring times can be arbitrarily set

2. The solder paste mixer operation panel instructions
The power switch activates the switching time of the relay governor

3. Paste mixer installation and caution

3.1 Installation
3.1.1 Please put the machine on the level of stability of the desktop or the ground, adjust the machine four feet to the level of the cup, to avoid the machine in the high speed mixing different sound or shake:
3.1.2 Please check the use of the machine voltage specifications (Ac220v) and the mains voltage specifications should be consistent, turn on single-phase 220v power supply;
3.1.3 Please confirm whether there is a loose screw, the machine should not have foreign objects in the flat, to avoid collision

3.2 Caution
3.2.1 Make sure that the machine is stable.
3.2.2 Paste the pot to be completely placed in the machine fixture. While stirring two cans of 500G solder paste cans, to stir 1000G of solder paste cans, along the separate replacement fixture.
3.2.3 Please turn the solder paste pot one turn and confirm that no collision will occur. Close the top cover of the machine and turn on the power switch.
3.2.4 Adjust the panel time to set the time to the best mixing time, about 5-8 minutes, depending on the solder paste brand and solder paste situation at that time.
3.2.5 Press the start switch, the running indicator light. The machine starts automatically high-speed mixing, until the completion of the machine automatically stops, open the cover automatically cut off the power supply.
3.2.6 After the job is finished, the operation stops, and the display shows the actual stirring time. In this case,
3.2.7 To stop the operation of the machine, press the power button, stop and cancel this operation.

4. Solder Paste Mixer Operation Procedure and Precautions

4.1 Operating Procedures
4.1.1 After commissioning, open the top cover of the machine and confirm that there is no foreign matter in the machine.
4.1.2 Rotate the angle of the solder paste fixture into the fixture of the machine. .
4.1.3 Turn the solder pot around with one hand to make sure that there is no collision. Cover the top cover and turn on the power switch.
4.1.4 Adjust the time on the panel to set the time to a better mixing time, depending on the solder paste brand
4.1.5 Press the start switch, the running indicator light. The machine automatically starts to stir at high speed until the machine stops automatically.
4.1.6 After the job is finished, the operation stops and the display shows the actual stirring time. Determine the machine stops running open the cover, remove the jig on the solder paste cans, then back to the temperature softening and mixing evenly paste can be used.
4.1.7 To stop the operation of the machine, press the power key, stop and cancel the operation.
4.1.8 Open the machine cover in operation, the machine will automatically stop running, will cover the cover to continue after the stirring operation, need to press the start switch.
4.1.9 After the number of production, turn off the power switch;

4.2 Precautions
4.2.1 End of the production operation To open the machine cover, you must wait until the machine is completely stopped and then open:
4.2.2 The weight difference between the left and right jigs of solder paste or weight shall not exceed 50 g. Otherwise, it will cause the machine to produce high-speed stirring in the case of shaking, please try to avoid;

5. Paste mixer periodic inspection and maintenance matters

1. Please keep the machine clean;
2. Check the screws without loosening;
3. Check the machine before running the switch with the cover with the sensitivity;
4. The machine bearings are fully enclosed, do not need to add lubricants.

6. Parameter
Power Supply: AC 220V/110V 50Hz 60Hz 40W Arm
Rotation Speed 1400 RPM Revolution
400RPM Speed ratio41 1400 RPM rotation350PRM
Paste mixer capacityContainer 500kg1000kg(The clamp should be replaced)
While stirring two cans of tin cans:500ed 1000g OneTwo container operation
Paste mixer stirring time: Working timer 199 Minute digit adjustable 1 Sec. 99Min
Paste mixer operation: Operational Touch paneleasy operation

7. Paste mixer fixture function
Holding Universal fixture for a variety of brand solder paste cans Suitable different kinds of solder past container
Paste mixer running noise Noise Low operating noise<35dB Low operation noise

8. Dimension and Weight
External : 410x410x460mm(LongWidthHeight)
Weight : 40KG